Home » News » Pumpkin Table Runner

Pumpkin Table Runner

Tyvek is a versatile product as it can be sewn or glued and doesn’t rip easily. Not only does it make it ideal for kite making but also for party table runners, especially themed children’s parties!

Get ready for Halloween with this spooky Pumpkin Table Runner designed by Kathleen Hauck…

Tools:
1802913 Soft-Cut Premium Line Scissors, 21 cm, black/blue
1802523 Comfortline Scalpel inc. 5 blades
1802526 Comfortline Cutting Mat, DIN A3, printed both sides
1802730 Aluminium Ruler, 30 cm
1812100 Lino and Wood Cutting Tool Set
1813100 Roller, 60 mm
1813300 Roller, 120 mm

Materials:
1600515 Tyvek Soft – DuPont, 70 x 100 cm, 44 g / m², white
1797010 Punch 4XL, Circle 3.5 Inch, 88 mm
Papier Offcut eg: 1549901 My Colors Cardstock snowbound
1851004 Lino Sheet, DIN A4, 3.2 mm
6000938 FolkArt Acrylic Paint, 59 ml, licorice
1055189 Foam Sheet, 300 x 450 x 2 mm, black
4550028 iZINK Textilfarbe, dalhia

In addition: a large sheet of paper, scrap paper, carbon paper, template, pencil, old lid

1. Cut the Tyvek in two lengthways so you have two 35 x 100 cm pieces. Cover your work surface and place a strip of Tyvek on it. Cut out 6 circles from the paper offcut and spread them over the Tyvek strip. Shake the textile spray before test spraying onto the scrap paper. Then spray the Tyvek table runner with the orange textile spray, paying particular attention to where the circles are. Leave to dry.

Tip: Tyvek can be sewn or glued together with contact adhesive if the table runner is too short.

2. Cut a piece of lino approx 26 x 7 cm. (Do this by cutting the lino upper surface with a scalpel. Then bend it in two to break it, cutting the woven back with the scalpel.) Place the carbon paper on the lino with the template on top. Trace the design with the pencil.

NB: The picture on the lino must always be a mirror image of the final design print. This is especially important to note when text is used.

3. Lino printing is a high-pressure process. This means that everything that remains on the lino’s surface will be visible when printing whilst everything that is cut away will not.

Cut out the contours of the pumpkins with the V shaped cutting blade. Use a slightly wider cutting tool to cut out the eyes, nose and mouth of the pumpkins. Then remove the lino surface around the pumpkins using the wide blade. Since the blades are very sharp, you should always work away from your body.

Tip: If the lino is too hard heat the surface with a hair dryer. When the lino is warm it becomes softer and easer to work with.

4. Place the foam sheet underneath the table runner wherever you want to stamp. Squeeze a little black acrylic paint onto the old lid and work it onto the small roller. Use the roller to cover the lino pumpkin design with a generous coat of paint. Position the lino face down on the table runner where you want to print the pumpkins. Use the clean large roller to slowly roll over the back of the lino, applying even pressure. Carefully lift the lino and re-ink it before printing your next image. Repeat as may times as desired. Then leave to dry.

You can download the template from Efco’s German website. (Clicking the link will open up another window with the German version of this project and you’ll find the template at the bottom of the page.)

Efco’s range of Tyvek products can be seen on Page 92 of the Basics Catalogue.

Posted in News and tagged as , , , , ,

Comments are closed.